CONFAST®

3/8" x 1-3/4" CONFAST® Hex Head Concrete Screw, 25/Box

(No reviews yet) Write a Review
SKU:
CSH38134
Availability:
In Stock, Ships Today!
$19.07

Description

Products Features 
  • COMPLETE ​LINE:  Ensures ​correct ​product ​can ​be ​located ​and ​purchased ​for ​any ​job 
  • ALL ​LENGTHS ​ARE ​AVAILABLE:  Using ​the ​correct ​length ​screw ​ensures ​quality, ​secure ​fastening 
  • SPECIAL ​THREADS: Decreases ​installation ​torque ​allowing ​screw ​to ​be ​installed ​faster and ​easier 
Products specifications
Bit Size 3/8"
Minimum Embedment 1-1/2"
Box Qty 25
Thread Type Low Torque Threads
2000 PSI Concrete - Pull-Out (lbs.) * 1590
2000 PSI Concrete - Shear (lbs.) * 2662
Type Male
Primary Concrete
Diameter 3/8"
Length 1-3/4"
Material Carbon Steel
Environment Dry
Minimum Spacing 6"
Minimum Edge Distance 3"
Wrench Size For Nut 9/16"
Length Measurement Underneath head
Brand Name CONFAST
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete

Environment
The anchor is designed for use in a dry environment.

Head Style
The anchor is a Hex Washer Serrated head and is designed to allow the head to sit on top of the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (Concrete). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required
A 9/16" is required for driving the anchor into the base material.

Diameter of Anchor
The diameter of the anchor is 3/8".

Length Anchor
The length of the anchor is 1-3/4"

Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.

Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Wrench Size
The size of the wrench required to turn the nut to set the anchor is 9/16".

Spacing between Anchors
Each anchor must be spaced a minimum distance of 6" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.

Holding Values - Ultimate Load Values in 2000 PSI Concrete

Anchor Size

Minimum Embedment

Pull-Out (lbs.)

Shear (lbs.)

3/8" x 1-3/4"

1-1/2"

1590

2662
Installing a 3/8" x 1-3/4" CONFAST® Hex Head Concrete Screw
  1. Drill a 3/8" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
  3. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
  4. Insert the point of the 3/8" x 1-3/4" CONFAST® Hex Head Concrete Screw into the hole..
  5. Turn the screw clockwise, applying slight pressure until the head of the screw is snug against the material being fastened.
  6. Always use proper personal protective equipment per manufacturer's and OSHA instructions.

View AllClose

Additional Information

Bit Size:
3/8"
Minimum Embedment:
1-1/2"
Box Qty:
25
Thread Type:
Low Torque Threads
2000 PSI Concrete - Pull-Out (lbs.) *:
1590
2000 PSI Concrete - Shear (lbs.) *:
2662
Type:
Male
Primary:
Concrete
Diameter:
3/8"
Length:
1-3/4"
Material:
Carbon Steel
Environment:
Dry
Minimum Spacing:
6"
Minimum Edge Distance:
3"
Wrench Size For Nut:
9/16"
Length Measurement:
Underneath head
Brand Name:
CONFAST
View AllClose

Related Products

Related Products